Please enable JavaScript.

Coggle requires JavaScript to display documents.

Klipper configuration, Temperature sensors - Coggle Diagram

- - - - hardware names used for pins - eg, PA4.
      - pin names may be preceded by
        
        ^
        
        enable hardware pull-up resistor for the pin
        
        ~
        
        enable hardware pull-down resistor for the pin
        
        !
        
        use reverse polarity (eg, trigger on low instead of high).
    - - Additional MCU pins
        
        "extra_mcu:ar9" is used elsewhere in the config ("ar9" is a hardware pin name or alias name on the given mcu).
  - - - [stepper]
        Stepper motor definitions
        e.g. [stepper_x], [stepper_x1], [stepper_y], [stepper_y1], [stepper_z], [stepper_z1], [stepper_z2]
        
        associated subsection
        
        TMC stepper driver configuration
        
        [tmc2130], [tmc2208], [tmc2209], [tmc2660], [tmc2240], [tmc5160],
        Configure an associated stepper motor driver via SPI bus or single wire UART. To use this feature, define a config section with eg, "tmc2130" prefix followed by the name of the corresponding stepper config section (for example, "[tmc2130 stepper_x]").
    - - [extruder]
        describe the heater parameters for the nozzle hotend and the stepper controlling the extruder.
        
        [heater_bed]
        describes the heated bed.
      - Bed level support
        
        [bed_mesh]
        Mesh Bed Leveling enables move transformations that offset the z axis based on a mesh generated from probed points.
        
        [bed_tilt]
        Bed tilt compensation to enable move transformations that account for a tilted bed.
        🚫Note that bed_mesh and bed_tilt are incompatible; both cannot be defined.
        
        [bed_screws]
        Tool to help adjust bed leveling screws. Enables a BED_SCREWS_ADJUST g-code command.
        
        [screws_tilt_adjust]
        Tool to help adjust bed screws tilt using Z probe. Enables a SCREWS_TILT_CALCULATE g-code command.
        
        [z_tilt]
        Multiple Z stepper tilt adjustment to enable independent adjustment of multiple (i.e. 2 or 3) z steppers (see the "stepper_z1" section) to adjust for tilt. Enables a Z_TILT_ADJUST extended G-Code command.
        
        1 more item...
        
        ⚠️When using a probe, recommended to define
        
        Customized homing
        
        G-Code macros and events
        
        Optional G-Code features
        
        Resonance compensation
        
        Config file helpers
        
        2 more items...
        
        [input_shaper]
        Enables resonance compensation.
        
        1 more item...
        
        [virtual_sdcard]
        A virtual sdcard allows the Klipper host software to directly print gcode files stored in a directory on the host using standard sdcard G-Code commands (eg, M24).
        
        [sdcard_loop]
        Some printers with stage-clearing features, such as a part ejector or a belt printer, can use looping sections of the sdcard file. (eg, to print the same part over and over, or repeat the a section of a part for a chain or other repeated pattern).
        
        1 more item...
        
        [gcode_macro]
        Custom G-Code macros eg, [gcode_macro my_cmd]
        
        [delayed_gcode]
        Execute a gcode on a set delay after printer enters ready state. It is useful for initialization procedures.
        
        [save_variables]
        Support saving variables to disk so that they are retained across restarts.
        
        [safe_z_home]
        Safe Z homing is used to home the Z axis at a specific X, Y coordinate eg, move to the center of the bed before homing Z.
        
        [homing_override]
        Homing override to run a series of g-code commands in place of a G28 found in the normal g-code input. ⚠️This may be useful on printers that require a specific procedure to home the machine.
        
        [endstop_phase]
        Stepper phase adjusted endstops to imoprove accuracy of endstop switches. eg, [endstop_phase stepper_z]"). Bare "[endstop_phase]" declaration enables ENDSTOP_PHASE_CALIBRATE command. 🚫Note It is not used with Sensorless Homing.
- - - - sub-sections
        follows predefined in format where predefined sub-section name is tied to a parent section. They extend a primary section with specialized settings (e.g., driver config under a stepper).
    - - Multi-line: Indented under the section.
        
        Key-value pairs: parameter: value (e.g., max_accel: 5000).
        
        Predefined key names under each section
        
        Comments: # comment or ; comment.
- - - - MAXxxxxx temperature sensors
        sensor_type:
        One of "MAX6675", "MAX31855", "MAX31856", or "MAX31865".