Please enable JavaScript.

Coggle requires JavaScript to display documents.

06FM201 BINDER MASS FLOWMETER - Coggle Diagram

- - - - 2024
        
        2025
        
        2 JANUARY
        Event: Clean-up cement from Rotary Valve going to FE202 (found hard and build-up cement around FM201 housing.
        Time: Day Shift
        
        13 JANUARY
        Event: Electrical Team to inspect the speed target of FM201.
        Time: Night Shift
        
        5 & 6 JANUARY
        Event: Installation of FM201, and electrical wiring connection and testing
        Time: Day Shift and Night Shift
        
        7 JANUARY
        Event: Assisted Electrical to test run FM201 Binder Mas Flowmeter
        Time: Night Shift
        
        18 JANUARY
        Event: Inspection of HP201 and FM201 - no blockages found, both equipment clean and no traces of build-up. Calibration of FM201 due to not achieve the setpoint of binder delivery, setpoint is 20tph but the present value 14tph only.
        Time: 0609H - 1010H
        Downtime (minutes): 241.2
        
        19 JANUARY
        Event: Binder Mass Flowmeter MCC fault, burnt smell coming from the equipment.
        Time: 0943H - 1158H
        Downtime (minutes): 135
        
        22 MARCH
        Event: Electrical Team conducted troubleshooting of Binder mas Flowmeter FM201 Motor.
        Time:1705H - 2242H
        Downtime (minutes): 336.28
        
        08 APRIL
        Event: FM201 - troubleshooting of binder system issues not reaching required amount of cement at 12%
        Time: 1103H - 1214H
        Downtime (minutes): 70.95
        
        14 JULY
        Event: Testing of FM201
        Time: 1030H - 1136H
        Downtime (minutes): 65
        
        29 AUGUST
        Event: Assisted Mechanical Team for the replacement of Binder Mass Flowmeter
        Time: Day Shift
        
        14 JANUARY
        Event: Inspection and cleaning of cement build-up at Binder Mass Flowmeter
        Time: Day Shift
        
        22 February & 2 APRIL
        Event: Inspection and cleaning of Binder Mass Flowmeter
        Time: Day Shift and Night Shift
        
        18 APRIL, 27 MAY & 4 JUNE
        event: Inspection and cleaning of binder mass flowmeter. Removed small piece of rubber which blocked two compartments of FM201 discharge
        Time: Day Shift
        
        12 SEPTEMBER
        Event: Calibration of FM201 and pull-out / reinstallation of FM201 spool
        Time: Day Shift
        
        5 NOVEMBER
        Event: Binder mass Flowmeter low flow
        Time: 2155H - 2246H
        Downtime (minutes): 51
        
        26 NOVEMBER
        Event: RV201 - unblocking of clogged up Binder Rotary Valve
        Time: 2350H - 0259H
        Downtime (minutes): 195
        
        1 DECEMBER
        Event: Electrical to bypass the FM201 Binder Mass Flowmeter due to stuck-up Motor. Stop paste filling due to leaking Binder Mass Flowmeter housing.
        Time: 1700H - 2000H, 2018H - 2338H
        Downtime (minutes): 379.8
        
        13 DCEMBER
        Event: Electrical to by-pass the FM201 Binder Mass Flowmeter due to stuck-up Motor
        Time: Day Shift
      - 15 JANUARY
        Event: FM201 tripped, Electrical decided to replace the soft starter.
        Time: 1220H - 1700H
        Downtime (minutes): 268.95
      - 15 JANUARY
        Event: FM201 communication fault
        Time: 1202H - 1351H
        Downtime (minutes): 103.95
      - 27 MARCH
        Event: Stop the Paste fill to give way to Electrical Team to rectify the issue at FM201
        Time: 1325H - 1543H
        Downtime (minutes): 183.88
      - 22 DECEMBER
        Event: Repair FM201 Binder Mass Flow Meter
        Time: 1458H - 1830H
        Downtime (minutes): 211.05
      - 6 JANUARY
        Event: Stop and start of binder mass flowmeter and no reading but in actual there was a discharge. Opened FM201 but no blockage
        Time: 1100H - 1158H
        Downtime (minutes): 58
      - 14 JANUARY
        Event: FM201 tripping numerous times without alarm reflected on the SCADA. Initial findings by Electrical was that there was loose connection in the power supply. To be rectified during shutdown.
        Time: 1520H - 1602H
        Downtime (minutes): 42
      - 18 JANUARY
        event: FM201 frequent tripping making the paste sequence faulted. Stopped filling to give way for Electrical Team to rectify issue.
        Time: 1030H - 1300H
        Downtime (minutes): 150
      - 26 & 28 JANUARY
        Event: Checking and assistance to Electrical personnel for the rectification of FM201
        Time: Day Shift
      - 10 & 18 APRIL
        Event: Inspection and cleaning of binder mass flowmeter to make sure that there are no chunk of cement blocking
        Time: Day Shift and Night Shift
      - 18 MAY, 21 JUNE & 7 JULY
        Event: Inspection and cleaning of binder mass flowmeter, removed chunks of cement and piece of steel.
        Time: Day Shift and Night Shift
      - 4 & 30 SEPTEMBER, 17 OCTOBER, 5, 13 & 26 NOVEMBER, 20 DECEMBER
        Event: Inspection and cleaning of binder mass flowmeter
        Time: Day Shift and Night Shift