Please enable JavaScript.
Coggle requires JavaScript to display documents.
DIRECT AIR
CAPTURE, DIRECT AIR
CAPTURE, RUN & CLIMATE TECH BEIJING…
DIRECT AIR
CAPTURE
Carbon dioxide is captured from the air using an electrochemical cell. This cell is used for direct air capture and ventilated air treatment. The productivity for capturing CO2 gas is greater than or equal to 0.003 kg of target gas per kg of bed per second at a gas stream flow rate of greater than or equal to 0.001 L/s and less than or equal to 500 L/s.
Autothermal direct air capture (ADAC) system involves exposing the sorbent to ambient CO2 gas volume, where the sorbent binds with CO2 while desorbing water.
A self-adaptive load system for photovoltaic power generation is utilized to capture carbon dioxide, seal and store air, enabling local consumption of solar power and collection of carbon dioxide.
A direct air capture system is used to capture CO2 from the atmosphere. The system utilizes a nanoporous material loaded with carbonate ions for CO2 adsorption. The dehumidified air should have a relative humidity of 15% to 35%, and the flow rate should be between 2000 m3/h and 2500 m3/h. The system also includes a CO2 adsorption material spraying device.
Capturing carbon dioxide (CO2) from the air is done using polyethyleneimine-silica adsorbent material in fluidized beds, comrises Circulating Fluidized Bed (CFB) adsorber and a Bubbling Fluidized Bed (BFB) desorber. The daily CO2 capture capacity is 40 tons.
Amine-functionalized mesoporous adsorbents have excellent initial CO2 adsorption capacities from ambient air, but degrade under realistic adsorption/desorption times and real atmosphere conditions.
HANDLECO2 is used to develop efficient cellulosic DAC chemisorbents utilizing robust bijels for the adsorption of CO2 from air.
The combination of photothermal adsorbent carbon materials, typically used as light-absorbing materials, and a polyamine-impregnated silica adsorbent, is an effective and sustainable method for the direct air capture (DAC) process. Both the photothermal adsorbent with carbon material and the nonphotothermal adsorbent without carbon material adsorb almost the same amount of CO2, approximately 45 mg-CO2 g–1.
Membrane-based CO2 capture and Ni-Ca based dual functional materials are combined for continuous direct air capture (m-DAC) and methanation (m-DAC-M). Ni-Ca/Al2O3 shows high CH4 productivity and selectivity with good stability over 100 hours
DIRECT AIR
CAPTURE
Carbon dioxide is captured from the air using an electrochemical cell. This cell is used for direct air capture and ventilated air treatment. The productivity for capturing CO2 gas is greater than or equal to 0.003 kg of target gas per kg of bed per second at a gas stream flow rate of greater than or equal to 0.001 L/s and less than or equal to 500 L/s.
Autothermal direct air capture (ADAC) system involves exposing the sorbent to ambient CO2 gas volume, where the sorbent binds with CO2 while desorbing water.
A self-adaptive load system for photovoltaic power generation is utilized to capture carbon dioxide, seal and store air, enabling local consumption of solar power and collection of carbon dioxide.
A direct air capture system is used to capture CO2 from the atmosphere. The system utilizes a nanoporous material loaded with carbonate ions for CO2 adsorption. The dehumidified air should have a relative humidity of 15% to 35%, and the flow rate should be between 2000 m3/h and 2500 m3/h. The system also includes a CO2 adsorption material spraying device.
Capturing carbon dioxide (CO2) from the air is done using polyethyleneimine-silica adsorbent material in fluidized beds, comrises Circulating Fluidized Bed (CFB) adsorber and a Bubbling Fluidized Bed (BFB) desorber. The daily CO2 capture capacity is 40 tons.
Amine-functionalized mesoporous adsorbents have excellent initial CO2 adsorption capacities from ambient air, but degrade under realistic adsorption/desorption times and real atmosphere conditions.
HANDLECO2 is used to develop efficient cellulosic DAC chemisorbents utilizing robust bijels for the adsorption of CO2 from air.
The combination of photothermal adsorbent carbon materials, typically used as light-absorbing materials, and a polyamine-impregnated silica adsorbent, is an effective and sustainable method for the direct air capture (DAC) process. Both the photothermal adsorbent with carbon material and the nonphotothermal adsorbent without carbon material adsorb almost the same amount of CO2, approximately 45 mg-CO2 g–1.
-
-
-
-
-
-
-
-
-