Please enable JavaScript.
Coggle requires JavaScript to display documents.
Gate Design, พีรวิชญ์ ชัยปัญญา 61070502035 - Coggle Diagram
Gate Design
Gate types
Tab Gates
มี 2 ส่วนคือ Tab and Side, แก้ปัญารอยย่นและความเค้นบนผิวชิ้นงาน, ไม่เหมาะกับพลาสติกหนืดสูง, มีรอยด้านข้างใหญ่
Edge Gates
gate ด้านข้างต้องตัดออกเอง, เกิดรอยด้านข้าง, อาจมีปัญหากับพลาสติกหนืดสูง
Spoke gate
คล้าย ring gate แต่ทางเข้ามี 4 ทิศทาง, เกิด weldline
Point Gates
ใช้กับชิ้นงานหลายๆ cavity, ไม่ใช้ runner กลม, ตัด gate อัตโนมัติ, ไม่เหมาะกับพลาสติกหนืดสูงหรือมีสารเติมแต่ง, ค่าบำรุงรักษามาก, มีรอย sear บนผิวชิ้นงาน
Sprue gate
เหมาะกับชิ้นงานใหญ่ๆ cavity เดียว,
เสียความดันน้อย, ไม่มี air trap and weld line, ไม่มีบ้อดักเศษ, gate ใหญ่ตัดยาก
Ring gate
เหมาะกับงานทรงกระบอก, รอย gate อยู่ผิวด้านนอก
Disc or diaphragm gate
เหมาะกับงานทรงกระบอก, ส่วนใหญ่เป็น cavity เดียว
Submarine/Tunnel Gates
ตัด gate อัตโนมัติ, ไม่มีรอย gate, เหมาะกับ semi crytalline
Film or Flash Gates
มี runner ขยายออกซ้าบขวา, พลาสติกไหลแผ่กว้าง, เหมาะกับงานบางๆ, ทำงานกับพลาสติกหนืดสูงได้, ไม่มีความเค้นตกค้าง, หอตัวสม่ำเสมอ, รอยด้านข้างยาว ตัด gate ยาก
Fan Gates
ช่วยให้พลาสติกไหลแบบแผ่กว้าง ไหลนิ่มขึ้น, เหมาะกับงานใหญ่ๆ แผ่นกว้างๆ งานหนาๆ, ลดการโก่งงอ, มีรอยด้านข้างชิ้นงาน
สิ่งที่ต้องพิจารณา
Gate location
balance Filling
Weldline position and strength
Cosmetic
Air trap position
Injection time
Clamping force
Gate geometry
depth (T)
width (W)
land (L)
Shrinkage
Holding time
Sinkmark
Injection pressure
Shear rate, shear stress
Number of gates
ยิ่งจำนวน gate มาก weldline ก็มากตามแต่แรงดันฉีดและเวลาจะน้อย
Type of gates
Sprue, Edge, Tap, Overlap, Pinpoint, Tunnel, Film (Flash), Fan, Disc (Diaphragm)
Factors affecting gate size
น้ำหนัก ขนาด ระยะการไหลและพื้นที่ของโพรงแบบมาก gate ต้องหนามากตามเพื่อลดความดันฉีด
ชิ้นงานที่ผนังหนา gate ต้องหนาตาม เพื่อไม่ให้ gate ปิดเร็วไป
พลาสติกหนืดมาก
gate ต้องหนาและกว้าง
ดังนั้นถ้า gate ใกล้ท่อหล่อเย็น
gate ต้อง
หนา ถ้า gate ไกลท่อหล่อเย็น gate ต้องบาง
ถ้า gate หนาฉีดเร็วได้มากขึ้น
Gate Location design Rules
Gate centrally to provide equal flow length
Gate symmetrically to avoid warpage
Gate into thicker sctions for better filling and packing
Gate long, narrow part from an end for uniform flow
Position the gate away from load-bearing areas
Hide the gate scar
Vent properly to prevent air traps
Gate for proper weld-line location and strong weld lines
Multiple gates shorten flow lengths
Gate location analysis
ตำแหน่งของ gate ที่ไม่เหมาะสมอาจทำให้ชิ้นงานมีความหนาไม่เท่ากันเนื่องจากความดันหลังฉีดเติมไม่เท่ากันทั้งชิ้นงาน จึงต้องวางตำแหน่ง gate ให้เหมาะสมเพื่อให้ความดันใกล้เคียงกันให้มากที่สุด
Shear rate at gate
พีรวิชญ์ ชัยปัญญา 61070502035